True
ID: 161
Views
223 Total Views
0 Members Views
223 Public Views
Share on Social Networks
Share Link
Use permanent link to share in social media
Share by mail

Please login to share this document by email.

Embed in your website
Select page to start with

8. DuPont Personal Protection DuPont de Nemours (Luxembourg) S.àr.l. L-2984 Luxembourg Tel.: +800 3666 6666 (international toll-free) Fax: +352 3666 5071 E-mail: personal.protection@lux.dupont.com Important Note The permeation data published have been generated for DuPont by independent accredited testing laboratories according to the test method applicable at that time (EN369, ASTM F739, EN 374-3, EN ISO 6529 (method A and B) or ASTM D6978) The data is typically the average of three fabrics samples tested. All chemicals have been tested at an assay of greater than 95 (w/w) % unless otherwise stated. The tests were performed at room temperature and environmental pressure unless otherwise stated. A different temperature may have significant influence on the breakthrough time. Permeation typically increases with temperature. Cumulative permeation data have been measured or have been calculated based on steady state permeation rate. Cytostatic drugs testing has been performed at a test temperature of 27°C according to ASTM D6978 or ISO 6529 with the additional requirement of reporting a normalized breakthrough time at 0.01 μg/cm²/min. Chemical warfare agents (Lewisite, Sarin, Soman, Mustard, Tabun and VX Nerve Agent) have been tested according to MIL-STD-282 at 22°C or according to FINABEL 0.7 at 37°C. Permeation data for Tyvek® is applicable to white Tyvek® 500/ Tyvek® 600 only and is not applicable for other Tyvek® styles or colours. Permeation data are usually measured for single chemicals. The permeation characteristics of mixtures can often deviate considerably from the behaviour of the individual chemicals. Please use the permeation data provided as a part of the risk assessment to assist with the selection of a protective fabric, garment or accessory suitable for your application. Breakthrough time is not the same as safe wear time. Breakthrough times are indicative of the barrier performance, but results can vary between the test methods and laboratories. Breakthrough time alone is insufficient to determine how long a garment may be worn once the garment has been contaminated. Safe user wear time may be longer or shorter than the breakthrough time depending on the permeation behaviour of the substance, the toxicity of the substance, working conditions and the exposure conditions (e.g. temperature, pressure, concentration, physical state). Latest Update Permeation Data: 30/05/2018 The garment does not protect against ionizing radiation. This garment and/or fabric are not flame resistant and should not be used around heat, open flame, sparks or in potentially flammable environments. The information provided herein corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials or additives or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. Technical_Description _ 1200 _ EN .pdf Printed on : March 1, 2019page of 8 8 For further product information, literature and as well as assistance in locating a local supplier, please visit: www.safespec.dupont.co.uk The footnotes can be found on the SafeSPEC™ website. Copyright © DuPont. All rights reserved. The DuPont Oval Logo, DuPont™, The miracles of science™ and all products denoted with ® or ™ are registered trademarks or trademarks of E. I. du Pont de Nemours and Company or its affiliates. Technical_Description_1200_EN.pdf Printed on : March 1, 2019

1. Product Description DuPont™ Tychem® 2000 C. Hooded coverall. Stitched and over-taped seams. Thumb loops. Elastication at wrists, ankles, face and waist. Self-adhesive double zipper flap and chin flap. Yellow. Certifications Certified according to Regulation (EU) 2016/425 Chemical protective clothing, Category III, Type 3-B, 4-B, 5-B and 6-B EN 14126 (barrier to infective agents), EN 1073-2 (protection against radioactive contamination) Antistatic treatment (EN 1149-5) - on inside Packaging ( Quantity/Box ) 25 per box, individually packed. EN 14126 EN 1149-5 EN 1073-2 T6 T5 T4 T3 CAT III Technical data sheet DuPont™ Tychem® 2000 C , TCCHA5TYL00 Size Article Number Chest Girth(cm) Body Height(cm) Chest Girth(in) Body Height(ft/in) SM D13494990 84-92 162-170 33-36 5'4"-5'7" MD D13494969 92-100 168-176 36-39 5'6"-5'9" LG D13395589 100-108 174-182 39-43 5'8"-6'0" XL D13395699 108-116 180-188 43-46 5'11"-5'2" 2X D13395560 116-124 186-194 46-49 6'1"-6'4" 3X D13494922 124-132 192-200 49-52 6'3"-6'7" Reference Number: TCCHA5TYL00 Technical_Description _ 1200 _ EN .pdf Printed on : March 1, 2019 page of 1 8

3. Comfort Property Test Method Result EN Class Air Permeability (Gurley method) ISO 5636-5 No N/A According to EN 14126 2 Front Tyvek ® / Back 5 Larger than > Smaller than < Not Applicable N/A Penetration and Repellency Property Test Method Result EN Class Resistance to Penetration by Liquids, Sulphuric Acid (30%) EN ISO 6530 <1 % 3 of 3 1 Resistance to Penetration by Liquids, Sodium Hydroxide (10%) EN ISO 6530 <1 % 3 of 3 1 Resistance to Penetration by Liquids, o-Xylene EN ISO 6530 <1 % 3 of 3 1 Resistance to Penetration by Liquids, Butan-1-ol EN ISO 6530 <1 % 3 of 3 1 Repellency to Liquids, Sulphuric Acid (30%) EN ISO 6530 >95 % 3 of 3 1 Repellency to Liquids, Sodium Hydroxide (10%) EN ISO 6530 >95 % 3 of 3 1 Repellency to Liquids, o-Xylene EN ISO 6530 >95 % 3 of 3 1 Repellency to Liquids, Butan-1-ol EN ISO 6530 >90 % 2 of 3 1 According to EN 14325 1 Larger than > Smaller than < Biological Barrier Property Test Method Result EN Class Resistance to Penetration by Blood-borne Pathogens using Bacteriophage Phi-X174 ISO 16604 Procedure C 20 kPa 6 of 6 2 Resistance to Penetration by Contaminated Liquids EN ISO 22610 >75 min 6 of 6 2 Resistance to Penetration by Biologically Contaminated Aerosols ISO/DIS 22611 log ratio >5 6 of 6 2 Resistance to Penetration by Contaminated Solid Particles ISO 22612 log cfu <1 3 of 3 2 According to EN 14126 2 Larger than > Smaller than < Technical_Description _ 1200 _ EN .pdf Printed on : March 1, 2019page of 3 8

7. Permeation Data for Tychem® 2000 C Hazard Name Physical State CAS BT Act BT 0.1 BT 1.0 EN SSPR MDPR Cum 480 Time 150 ISO ISO Thiotepa (10 mg/ml) Liquid 52-24-4 10 >240 >240 5 <0.005 0.001 Toluene Liquid 108-88-3 imm imm imm 503 0.033 ppm Toluene diisocyanate, 2,4- Liquid 584-84-9 imm imm imm 42 0.00000208 Trichloro benzene, 1,2,4- Liquid 120-82-1 imm imm imm 8.4 0.001 Vinyl cyanide Liquid 107-13-1 imm imm imm 10.6 0.005 (Actual) Breakthrough time at MDPR [mins] BT Act Normalized breakthrough time at 0.1 μg/cm²/min [mins] BT 0.1 Normalized breakthrough time at 1.0 μg/cm²/min [mins] BT 1.0 Classification according to EN 14325 EN Steady state permeation rate [μg/cm²/min] SSPR Minimum detectable permeation rate [μg/cm²/min] MDPR Cumulative permeation mass after 480 mins [μg/cm²] CUM 480 Time to reach cumulative permeation Time 150 mass of 150 μg/cm² [mins] Classification according to ISO 16602 ISO Chemical abstracts service registry number CAS Minutes mins Larger than > Smaller than < Immediate (< 4 min) imm Not tested nm Saturated solution sat Not Applicable N/A Based on lowest single value * Not attained na Actual breakthrough time; normalized breakthrough time is not available 8 Technical_Description _ 1200 _ EN .pdf Printed on : March 1, 2019 page of 7 8

2. Physical Properties Property Test Method Result EN Class Colour N/A Yellow N/A Basis Weight DIN EN ISO 536 83 g/m 2 N/A Thickness DIN EN ISO 534 180 μm N/A Abrasion Resistance 7 EN 530 Method 2 >1500 cycles 5 of 6 1 Flex Cracking Resistance 7 EN ISO 7854 Method B >5000 cycles 3 of 6 1 Flex Cracking Resistance at -30 °C EN ISO 7854 Method B >500 cycles N/A Trapezoidal Tear Resistance (MD) EN ISO 9073-4 35 N 1 of 6 1 Trapezoidal Tear Resistance (XD) EN ISO 9073-4 30 N 1 of 6 1 Tensile Strength (MD) DIN EN ISO 13934-1 160 N 3 of 6 1 Tensile Strength (XD) DIN EN ISO 13934-1 150 N 3 of 6 1 Puncture Resistance EN 863 18 N 2 of 6 1 Resistance to Water Penetration DIN EN 20811 >30 kPa N/A Surface Resistance at RH 25%, inside 7 EN 1149-1 < 2,5 • 10 Ohm 9 N/A Surface Resistance at RH 25%, outside 7 EN 1149-1 No antistatic treatment N/A Exposure to high Temperature N/A Garments seams opens at ~98 °C N/A Exposure to low Temperature N/A Flexibility retained down to -73 °C N/A Resistance to Ignition 7 EN 13274-4 Method 3 No after flame, no drop formation, hole formation N/A Bursting Strength (Mullenburst) ISO 2758 475 kPa N/A According to EN 14325 1 According to EN 14126 2 According to EN 1073-2 3 According to EN 14116 4 According to EN 11612 12 Front Tyvek ® / Back 5 Based on test according to ASTM D-572 6 See 7 Instructions for Use for further information, limitations and warnings Larger than > Smaller than < Not Applicable N/A Standard Deviation STD DEV Garment Performance Property Test Method Result EN Class Type 3: Resistance to Penetration by Liquids (Jet Test) EN 17491-3 Pass N/A Type 4: Resistance to Penetration by Liquids (High Level Spray Test) EN ISO 17491-4, Method B Pass N/A Type 5: Inward Leakage of Airborne Solid Particulates EN ISO 13982-2 Pass N/A Type 6: Resistance to Penetration by Liquids (Low Level Spray Test) EN ISO 17491-4, Method A Pass N/A Nominal protection factor 7 EN 1073-2 >5 1 of 3 3 Seam Strength EN ISO 13935-2 >125 N 4 of 6 1 Shelf Life 7 N/A 10 years 6 N/A According to EN 14325 1 According to EN 1073-2 3 According to EN 11612 12 According to EN 11611 13 Front Tyvek ® / Back 5 Based on test according to ASTM D-572 6 See Instructions for Use for further 7 information, limitations and warnings Based on the average of 10 suits, 3 activities, 3 probes 11 Larger than > Smaller than < Not Applicable N/A Based on lowest single value * Technical_Description _ 1200 _ EN .pdf Printed on : March 1, 2019 page of 2 8

4. Permeation Data for Tychem® 2000 C Hazard Name Physical State CAS BT Act BT 0.1 BT 1.0 EN SSPR MDPR Cum 480 Time 150 ISO Acetic acid (10%) Liquid 64-19-7 >480 >480 >480 6 <0.04 0.04 <19.2 >480 6 Acetic acid (2%) Liquid 64-19-7 >480 >480 >480 6 <0.04 0.04 <19.2 >480 6 Acetic acid (>95%) Liquid 64-19-7 imm imm imm 3 0.05 ppm Acetic acid ethyl ester Liquid 141-78-6 imm imm imm 12.7 0.11 ppm Acetone Liquid 67-64-1 imm imm nm 9.7 0.11 ppm Acetonitrile Liquid 75-05-8 imm imm imm 16 0.23 ppm Acroleic acid Liquid 79-10-7 imm imm imm 5.4 0.2 Acrylic acid Liquid 79-10-7 imm imm imm 5.4 0.2 Acrylonitrile Liquid 107-13-1 imm imm imm 10.6 0.005 Amino benzene Liquid 62-53-3 imm imm imm 2.1 0.14 Ammonia (gaseous) Vapor 7664-41-7 imm imm imm 3.1 0.001 Ammonium hydroxide (28%) Liquid 1336-21-6 imm imm imm 62 0.035 Aniline Liquid 62-53-3 imm imm imm 2.1 0.14 Benzenamine Liquid 62-53-3 imm imm imm 2.1 0.14 Bromine Liquid 7726-95-6 imm imm imm >50 0.0064 Butadiene, 1,3- (gaseous) Vapor 106-99-0 imm imm imm >17 0.001 Butanal, n- Liquid 123-72-8 imm imm imm 22 0.0063 Butanol, 1- Liquid 71-36-3 imm imm imm 1.6 0.057 ppm Butanol, n- Liquid 71-36-3 imm imm imm 1.6 0.057 ppm Butyl alcohol, n- Liquid 71-36-3 imm imm imm 1.6 0.057 ppm Butyraldehyde, n- Liquid 123-72-8 imm imm imm 22 0.0063 Carbon disulfide Liquid 75-15-0 imm imm imm 4367 0.0057 ppm Carboplatin (10 mg/ml) Liquid 441575-94-4 >240 >240 >240 5 <0.001 0.001 Carmustine (3.3 mg/ml, 10 % Ethanol) Liquid 154-93-8 30 >240 >240 5 0.002 0.001 Caustic ammonia (28%) Liquid 1336-21-6 imm imm imm 62 0.035 Caustic soda (42%) Liquid 1310-73-2 >480 >480 >480 6 <0.005 0.005 <2.4 >480 6 Caustic soda (50% at 50 °C) Liquid 1310-73-2 >480 >480 >480 6 <0.02 0.02 <9.6 >480 6 Caustic soda (50%) Liquid 1310-73-2 >480 >480 >480 6 <0.005 0.005 <2.4 >480 6 Chlorine (gaseous) Vapor 7782-50-5 imm imm imm >50 0.2 Chloro ethanol, 2- Liquid 107-07-3 imm imm imm 3.1 0.06 ppm Chromic acid (CrO3) (44.9%) Liquid 1333-82-0 >480 >480 >480 6 <0.07 0.07 <33.6 >480 6 Chromic acid (H2SO4 x CrO3) (80%) Liquid 1333-82-0 >480 >480 >480 6 <0.005 0.005 <2.4 >480 6 Cisplatin (1 mg/ml) Liquid 15663-27-1 >240 >240 >240 5 <0.002 0.002 Cyanoethylene Liquid 107-13-1 imm imm imm 10.6 0.005 Cyanomethane Liquid 75-05-8 imm imm imm 16 0.23 ppm Cyclo phosphamide (20 mg/ml) Liquid 50-18-0 <10* >240 >240 5 <0.002 0.002 Dichloro methane Liquid 75-09-2 imm imm imm >50 0.001 Diesel automotive test fuel Liquid mix imm imm imm 3.29 0.01 Diethyl amine Liquid 109-89-7 imm imm imm 64.3 0.017 ppm (Actual) Breakthrough time at MDPR [mins] BT Act Normalized breakthrough time at 0.1 μg/cm²/min [mins] BT 0.1 Normalized breakthrough time at 1.0 μg/cm²/min [mins] BT 1.0 Classification according to EN 14325 EN Steady state permeation rate [μg/cm²/min] SSPR Minimum detectable permeation rate [μg/cm²/min] MDPR Cumulative permeation mass after 480 mins [μg/cm²] CUM 480 Time to reach cumulative permeation Time 150 mass of 150 μg/cm² [mins] Classification according to ISO 16602 ISO Chemical abstracts service registry number CAS Minutes mins Larger than > Smaller than < Immediate (< 4 min) imm Not tested nm Saturated solution sat Not Applicable N/A Based on lowest single value * Not attained na Actual breakthrough time; normalized breakthrough time is not available 8 Technical_Description _ 1200 _ EN .pdf Printed on : March 1, 2019 page of 4 8

5. Permeation Data for Tychem® 2000 C Hazard Name Physical State CAS BT Act BT 0.1 BT 1.0 EN SSPR MDPR Cum 480 Time 150 ISO Dimethyl ketal Liquid 67-64-1 imm imm nm 9.7 0.11 ppm Dimethyl ketone Liquid 67-64-1 imm imm nm 9.7 0.11 ppm Doxorubicin HCl (2 mg/ml) Liquid 25136-40-9 >240 >240 >240 5 <0.007 0.007 Epoxy ethane (gaseous) Vapor 75-21-8 imm imm imm 170 0.02 Ethane 1,2-diol Liquid 107-21-1 >480 >480 >480 6 <0.05 0.05 <24 >480 6 Ethane nitrile Liquid 75-05-8 imm imm imm 16 0.23 ppm Ethyl acetate Liquid 141-78-6 imm imm imm 12.7 0.11 ppm Ethyl ethanamine, N- Liquid 109-89-7 imm imm imm 64.3 0.017 ppm Ethyl nitrile Liquid 75-05-8 imm imm imm 16 0.23 ppm Ethylene carboxylic acid Liquid 79-10-7 imm imm imm 5.4 0.2 Ethylene chlorohydrin Liquid 107-07-3 imm imm imm 3.1 0.06 ppm Ethylene glycol Liquid 107-21-1 >480 >480 >480 6 <0.05 0.05 <24 >480 6 Ethylene oxide (gaseous) Vapor 75-21-8 imm imm imm 170 0.02 Ethylene tetrachloride Liquid 127-18-4 imm imm imm >400 0.11 ppm Etoposide (Toposar®, Teva) (20 mg/ml, 33.2 % (v/v) Ethanol) Liquid 33419-42-0 >240 >240 >240 5 <0.01 <0.01 Ferric (III) chloride (40%) Liquid 7705-08-0 >480 >480 >480 6 <0.005 0.005 <2.5 >480 6 Fluorosilicic acid (33-35%) Liquid 16961-83-4 >480 >480 >480 6 <0.04 0.04 <19.2 >480 6 Fluorouracil, 5- (50 mg/ml) Liquid 51-21-8 >240 >240 >240 5 <0.002 0.002 Formaldehyde (10%) Liquid 50-00-0 >480 >480 >480 6 <0.1 0.1 <48 >480 6 Formaldehyde (37%) Liquid 50-00-0 imm imm >480 6 0.31 0.1 Formalin (10%) Liquid 50-00-0 >480 >480 >480 6 <0.1 0.1 <48 >480 6 Formalin (37%) Liquid 50-00-0 imm imm >480 6 0.31 0.1 Fuel-oil no 2 Liquid 68476-30-2 imm imm imm 1.776 0.01 Gemcitabine (38 mg/ml) Liquid 95058-81-4 15* >240 >240 5 <0.01 0.003 Glycol alcohol Liquid 107-21-1 >480 >480 >480 6 <0.05 0.05 <24 >480 6 Glycol chlorohydrin Liquid 107-07-3 imm imm imm 3.1 0.06 ppm Hydrochloric acid (32%) Liquid 7647-01-0 >480 >480 >480 6 <0.001 0.001 Hydrochloric acid (37%) Liquid 7647-01-0 60* 265* >480 6 0.46 0.001 Hydrofluoric acid (48%) Liquid 7664-39-3 7 17 >480 6 N/A 0.005 134 >480 6 Hydrofluoric acid (60%) Liquid 7664-39-3 imm 6 81 3 n/a 0.005 Hydrofluoric acid (70%) Liquid 7664-39-3 imm imm 15* 1 15.3 0.1 Hydrogen peroxide (50%) Liquid 7722-84-1 >480 >480 >480 6 <0.01 0.01 <4.8 >480 6 Hydrogen peroxide (70%) Liquid 7722-84-1 >480 >480 >480 6 <0.02 0.02 <10 >480 6 Ifosfamide (50 mg/ml) Liquid 3778-73-2 >240 >240 >240 5 <0.009 0.009 Iodomethane Liquid 74-88-4 imm imm imm nm 0.07 4550 μg/cm² , 8 min <1 Isopropanol Liquid 67-63-0 imm imm imm 8 0.04 Isopropyl alcohol Liquid 67-63-0 imm imm imm 8 0.04 Ketone propane Liquid 67-64-1 imm imm nm 9.7 0.11 ppm Limonene d- Liquid 5989-27-5 imm imm imm 29.8 0.02 (Actual) Breakthrough time at MDPR [mins] BT Act Normalized breakthrough time at 0.1 μg/cm²/min [mins] BT 0.1 Normalized breakthrough time at 1.0 μg/cm²/min [mins] BT 1.0 Classification according to EN 14325 EN Steady state permeation rate [μg/cm²/min] SSPR Minimum detectable permeation rate [μg/cm²/min] MDPR Cumulative permeation mass after 480 mins [μg/cm²] CUM 480 Time to reach cumulative permeation Time 150 mass of 150 μg/cm² [mins] Classification according to ISO 16602 ISO Chemical abstracts service registry number CAS Minutes mins Larger than > Smaller than < Immediate (< 4 min) imm Not tested nm Saturated solution sat Not Applicable N/A Based on lowest single value * Not attained na Actual breakthrough time; normalized breakthrough time is not available 8 Technical_Description _ 1200 _ EN .pdf Printed on : March 1, 2019 page of 5 8

6. Permeation Data for Tychem® 2000 C Hazard Name Physical State CAS BT Act BT 0.1 BT 1.0 EN SSPR MDPR Cum 480 Time 150 ISO Mercury Liquid 7439-97-6 >480 >480 >480 6 <0.09 0.09 <43.2 >480 6 Methanol Liquid 67-56-1 imm imm imm 2.2 0.18 ppm Methotrexate (25 mg/ml, 0.1 N NaOH) Liquid 59-05-2 >240 >240 >240 5 <0.001 0.001 Methyl 4-isopropenyl-1-cyclohexene, 1- Liquid 5989-27-5 imm imm imm 29.8 0.02 Methyl acetyl Liquid 67-64-1 imm imm nm 9.7 0.11 ppm Methyl benzol Liquid 108-88-3 imm imm imm 503 0.033 ppm Methyl cyanide Liquid 75-05-8 imm imm imm 16 0.23 ppm Methyl iodide Liquid 74-88-4 imm imm imm nm 0.07 4550 μg/cm² , 8 min <1 Methyl ketone Liquid 67-64-1 imm imm nm 9.7 0.11 ppm Methylene chloride Liquid 75-09-2 imm imm imm >50 0.001 Mitomycin (0.5 mg/ml) Liquid 50-07-7 >240 >240 >240 5 <0.002 0.002 Nitric acid (70%) Liquid 7697-37-2 >480 >480 >480 6 <0.01 0.01 <4.8 >480 6 Nitro benzene Liquid 98-95-3 imm imm imm 17.7 0.001 Oleum (30%) Liquid 8014-95-7 18 82 105 3 nm 0.005 Oxaliplatin (5 mg/ml) Liquid 63121-00-6 145 >240 >240 5 <0.1 0.008 Paclitaxel (Hospira) (6 mg/ml, 49.7 % (v/v) Ethanol) Liquid 33069-62-4 >240 >240 >240 5 <0.01 <0.01 Perchloric acid (70%) Liquid 7601-90-3 >480 >480 >480 6 <0.005 0.005 <2.4 >480 6 Phenyl amine Liquid 62-53-3 imm imm imm 2.1 0.14 Phosphoric acid (85%) Liquid 7664-38-2 >480 >480 >480 6 <0.005 0.005 <2.4 >480 6 Potassium chromate (sat) Liquid 7789-00-6 >480 >480 >480 6 <0.01 0.01 <4.8 >480 6 Potassium hydroxide (50%) Liquid 1310-58-3 >480 >480 >480 6 <0.005 0.005 <2.4 >480 6 Propan -2-ol Liquid 67-63-0 imm imm imm 8 0.04 Propan -2-one Liquid 67-64-1 imm imm nm 9.7 0.11 ppm Propene acid Liquid 79-10-7 imm imm imm 5.4 0.2 Propenenitrile, 2- Liquid 107-13-1 imm imm imm 10.6 0.005 Propenoic acid nitrile Liquid 107-13-1 imm imm imm 10.6 0.005 Pyroacetic ether Liquid 67-64-1 imm imm nm 9.7 0.11 ppm Sodium cyanide (sat) Liquid 143-33-9 >480 >480 >480 6 <0.07 0.07 <33.6 >480 6 Sodium fluoride (sat) Liquid 7681-49-4 >480 >480 >480 6 <0.005 0.005 <2.4 >480 6 Sodium hydroxide (42%) Liquid 1310-73-2 >480 >480 >480 6 <0.005 0.005 <2.4 >480 6 Sodium hydroxide (50% at 50 °C) Liquid 1310-73-2 >480 >480 >480 6 <0.02 0.02 <9.6 >480 6 Sodium hydroxide (50%) Liquid 1310-73-2 >480 >480 >480 6 <0.005 0.005 <2.4 >480 6 Sodium hypochlorite (15%) Liquid 7681-52-9 >480 >480 >480 6 <0.05 0.05 <24 >480 6 Sulfuric acid (50%) Liquid 7664-93-9 >480 >480 >480 6 <0.01 0.01 <4.8 >480 6 Sulfuric acid (98% at 50 °C) Liquid 7664-93-9 >480 >480 >480 6 <0.02 0.02 <9.6 >480 6 Sulfuric acid (>95%) Liquid 7664-93-9 >480 >480 >480 6 <0.02 0.020 <9.6 >480 6 Sulfuric acid fuming (30%) Liquid 8014-95-7 18 82 105 3 nm 0.005 Tetrachloro ethylene, 1,1,2,2- Liquid 127-18-4 imm imm imm >400 0.11 ppm Tetrahydrofuran Liquid 109-99-9 imm imm imm 183 0.11 ppm (Actual) Breakthrough time at MDPR [mins] BT Act Normalized breakthrough time at 0.1 μg/cm²/min [mins] BT 0.1 Normalized breakthrough time at 1.0 μg/cm²/min [mins] BT 1.0 Classification according to EN 14325 EN Steady state permeation rate [μg/cm²/min] SSPR Minimum detectable permeation rate [μg/cm²/min] MDPR Cumulative permeation mass after 480 mins [μg/cm²] CUM 480 Time to reach cumulative permeation Time 150 mass of 150 μg/cm² [mins] Classification according to ISO 16602 ISO Chemical abstracts service registry number CAS Minutes mins Larger than > Smaller than < Immediate (< 4 min) imm Not tested nm Saturated solution sat Not Applicable N/A Based on lowest single value * Not attained na Actual breakthrough time; normalized breakthrough time is not available 8 Technical_Description _ 1200 _ EN .pdf Printed on : March 1, 2019 page of 6 8

D-S ios app

To install this Web App in your iPhone/iPad press D-S ios app and then Add to Home Screen.